Skip to content

We'll ring you back

Leave your number and a time that suits you: we'll call to talk through your project or a light.

We only use your number to call you back. See our privacy policy.

Basket

Your basket is empty

Article: Lath-and-Plaster Ceilings, Ceiling Roses and Heavier Lights

A low-beamed English cottage sitting room with deep red walls and an inglenook log fire, a travertine flush ceiling light lit between dark oak beams, leaded window at blue hour

Lath-and-Plaster Ceilings, Ceiling Roses and Heavier Lights

Fixing a light to an old lath and plaster ceiling comes down to one rule: fix into timber, never into the plaster alone. The bracket goes into a ceiling joist, or into a length of timber screwed in between two joists. BS 7671, the British wiring standard, has long asked that a pendant's fixing can hold at least 5 kg, and that the ceiling is fit for the light's weight. So check the weight before you order.

Lath and plaster is not as fragile as its reputation. Plenty of these ceilings have been up for well over a century. What they dislike is extra weight, water and careless drilling. Below: how to recognise one, how heavy a light can be, and what to do about the decorative plaster rose in the middle.

How to tell if your ceiling is lath and plaster

A lath-and-plaster ceiling is a coat of plaster spread over thin strips of timber, the laths, nailed under the joists. The wet plaster was pressed through the narrow gaps between the strips, where it set into small lumps that grip the laths and hold the thin layer up. These lumps are known as nibs. The laths themselves are usually oak or pine.

Plasterboard gradually took its place over the course of the twentieth century. So the age of the house is a first clue: an original ceiling in a Georgian, Victorian or Edwardian house is very likely to be lath and plaster, while a later house could have either. Many old ceilings have also been replaced or covered with board over the years, so look before you assume.

  • From the loft. Between the joists you see the back of the ceiling. Rows of narrow wooden strips with lumps of old plaster between them mean lath and plaster. Flat sheets mean board.
  • At the old light point. When the old light comes down (with the power off at the consumer unit), the edge of the hole shows a layer of plaster over strips of wood, or a single board.
  • When in doubt. Treat it as lath and plaster. The fixing advice below is the safe choice for either kind of ceiling.

Why the plaster can't carry the light on its own

The plaster layer is thin, and it hangs from those nibs. A structural engineer writing in The Building Conservation Directory names water getting in as a particular risk to old ceilings, along with overloading from things stored in the loft above, and careless cuts into the supporting timbers to make way for pipes and cables. A light screwed only into the plaster adds a load in one spot that the nibs were never meant to take. Laths also split easily, and the plastic plugs sold for plasterboard don't grip them well.

Look at the ceiling around the light point before you choose anything. If it is bowing, sagging or cracked, have it looked at by someone who repairs traditional plaster before a new light goes up.

The 5 kg rule, and what your light weighs

The 5 kg figure is a minimum for the fixing, not a limit for the light. Above 5 kg, the fixing has to be rated for everything the light weighs. On a lath-and-plaster ceiling, the fixing is the timber above, so even a light well under 5 kg belongs in a joist or batten.

The weight should be on the product page. Here is what a few of ours say:

Light Weight on the product page What it means for the fixing
Rye, ceramic pendant About 700 g Light. Fix its 12 cm ceiling rose into timber as usual
Helmsley, travertine and walnut ceiling light About 1.1 kg Light enough, its page says, for the existing light point, with no reinforcement
Ambleside, metal disc pendant 2 kg (25 cm) or 2.8 kg (40 cm) Under 5 kg. Into timber
Hexham, a low travertine basin About 2.8, 4.8 or 7.7 kg (30, 43 or 55 cm) The 55 cm is over 5 kg: the fixing must carry its full weight, and two people make the job easier
Tetbury and Castleton Not given Ask us before you order

Stone is heavy for its size. Tetbury, a genuine travertine disc fixed flat to the ceiling in 38, 48 or 58 cm, should go into a joist or batten like any stone light. Castleton, the alabaster chandelier, comes with anything from a single disc, 20 cm across, to 27 discs spanning 70 cm, the biggest version reaching a 4 m drop. It is delivered in parts to put together, and an electrician can do the assembly and the connection for you if you prefer. Tell us which version you have in mind and ask for its weight first.

Finding the timber: joists and battens

A joist and cable detector, run slowly across the ceiling, shows where the joists are and where any cables run. Use it before drilling anything. Mark both with masking tape.

If the joist sits right above the light point, the bracket can screw straight into it. Often the point falls between two joists. The usual answer is a timber batten, sometimes called a noggin, fixed between them, so the bracket has something solid to bite into. That work is often easier from the loft, or from under the floorboards of the room above, than from below. If the light is heavy and there is no joist where you need one, this is a good moment to call an electrician. Doubt is reason enough.

Two more checks. If the ceiling has a textured coating such as Artex, and the house was built or refurbished before 2000, the coating may contain asbestos: the HSE notes it can be found in any home of that age. Don't sand or scrape it, and have it tested before you drill. And if the wiring at the light point looks old, or there is no earth wire, read our guide to light fittings in homes with no earth wire before going further.

Ceiling roses: the plaster one and the electrical one

In a British house, "ceiling rose" means two things. The electrical ceiling rose is the small round fitting where a pendant's flex meets the wiring. The decorative ceiling rose is the plaster moulding around it, often with leaves or flowers in relief. People searching for one often mean the other.

An original plaster rose is worth keeping. A few habits protect it:

  • Fix through it, not into it. The new bracket goes into the timber above. The moulding carries nothing.
  • Measure its flat centre. The canopy of the new light (the cup against the ceiling) looks best when it sits inside the plain middle of the rose. Rye's ceiling rose, for example, is 12 cm across.
  • Choose a pendant if you want to see it. A flush disc such as Tetbury sits tight against the ceiling, so over a moulded rose it would hide the plasterwork and could not sit flat on it. Save flush lights for plain ceilings.

If the plaster rose is cracked or loose, have it repaired before anything new hangs beneath it.

Listed building? Ask before you drill

In England, the Planning (Listed Buildings and Conservation Areas) Act 1990 makes consent a requirement for any work that would affect a listed building's character, and doing such work without it is an offence. Wales and Scotland each have their own legislation to the same effect, and Northern Ireland has its own system too. The government's listing guidance says protection applies to the whole building, not just its exterior, so a historic plaster ceiling or rose can be covered. Before you cut, chase or replace historic plaster, or fix into old beams, check with your local conservation officer at the planning authority.

Before you start: a short checklist

  1. Ceiling type checked, from the loft or at the old light point.
  2. Weight of the new light read on its product page, or asked for.
  3. Joists found with a detector, and a batten planned if the point sits between two.
  4. Canopy size compared with the flat centre of the plaster rose.
  5. Textured ceiling in a pre-2000 house tested for asbestos before drilling.
  6. Consent checked if the house is listed.
  7. Power off at the consumer unit, and proved off with a two-pole voltage tester before anything is touched.

The rest of the job, from switching off to connecting the new light, is covered step by step in our fitting guide, and the checks before you begin are in changing a ceiling light: what to check first. If your rooms are tall as well as old, lighting a high-ceilinged room covers drops and flex lengths, and lighting a Victorian house goes room by room. Browse our ceiling lights with the weight question in mind.

One last habit: before ordering anything for an old ceiling, write down three numbers, the ceiling height, the width of the rose's flat centre and the weight of the light. Our free guide, The Room-by-Room Lighting Guide, sets them alongside the other checks on its "Older British homes" page.

Read more

A sage hallway with a gilt mirror over a demilune console lit by a brass picture light, daylight
Fitting & Safety

Wall Lights Without Wiring: Plug-In, Rechargeable and Picture Lights

No wall light point? You can still light a wall. How rechargeable lights, plug-in wall lights and cordless lamps compare on brightness and run time, and what renters can do without drilling.

Read more
An oxblood limewashed landing with two travertine half-moon wall lights lit above an upholstered bench, staircase at the side, sunlight on the wall
Fitting & Safety

No Earth Wire? Light Fittings in Older Homes

British homes wired before 1966 may have no earth at the light points. How to tell, why it matters for metal and Class I lights, what the double-square symbol means, and the safe ways forward, best...

Read more