Passer au contenu

On vous rappelle

Laissez votre numéro et le moment qui vous arrange : nous vous appelons pour parler de votre projet ou d'un luminaire.

Votre numéro sert uniquement à vous rappeler. Voir notre politique de confidentialité.

Panier

Votre panier est vide

Article : Changing a Ceiling Light: What to Check Before You Start

An oxblood limewashed landing seen from below with a small tinted glass flush ceiling light lit on the ceiling, daytime

Changing a Ceiling Light: What to Check Before You Start

How do you change a ceiling light in the UK safely? Most of the work happens before you touch a wire. Check that the new light suits your ceiling height and that the fixing can carry its weight, turn the power off at the consumer unit, confirm with a proper tester that nothing is live, and photograph what is inside the old ceiling rose. If what you find doesn't look like a simple swap, stop there: an electrician can do this for you if you prefer.

This is a checklist, not a wiring guide. The connections depend on your light, so follow its instructions and our fitting guide, which sets out each step in order.

Before the day: four checks

1. Will it hang at the right height?

Where people walk underneath, The Room-by-Room Lighting Guide suggests keeping the bottom of a light at least about 2.1 m from the floor. Measure your ceiling, then look at how the drop works. Kendal, a travertine disc pendant, has a 150 cm cable that adjusts to the height you want and copes with a sloping ceiling of up to 30°, and its page asks for a ceiling height of at least 2.4 m. Harrow is the other case: its drop is fixed and cannot be adjusted, so bear it in mind under a low ceiling. If yours is low, our guide to lighting for low ceilings has more ideas.

2. Can the fixing carry it?

The usual benchmark, taken from the wiring regulations, is a fixing that can take 5 kg or more. Above that weight, the light needs something able to bear all of it: in practice a ceiling joist, or a timber batten (a "noggin") fitted between two joists. Look for the weight on the product page, and if it isn't given, email us before you fit the light.

Two examples from our range: Helmsley, a small travertine ceiling light trimmed with walnut, weighs about 1.1 kg, so your existing light point can carry it without reinforcing the ceiling. Lymington, a glass pendant with a scalloped rim, weighs approximately 1 kg and has a 10 cm ceiling rose.

3. What is the ceiling made of?

Lath and plaster, common in older homes, is plaster laid over thin strips of wood. The laths split easily and plasterboard plugs don't grip them well, so anything with weight goes into a joist. Our article on fixing a light to a lath and plaster ceiling goes into the detail.

Textured finishes need a different kind of care. The HSE points out that asbestos can be found in any building built or refurbished before 2000, including in textured decorative coatings such as Artex. Don't sand or scrape a textured ceiling, and have it tested before you drill new holes.

4. Do you have the right tester?

The tool that matters is a two-pole voltage tester of the kind described in the HSE's guidance note GS38. Electrical Safety First's guide to safe isolation advises against multimeters, makeshift devices and non-contact "voltage sticks" for this job: a non-contact tester can show that a cable is live, but it cannot prove that it is dead. Add a sturdy stepladder, a head torch (the room light will be off), insulated screwdrivers, a cable detector if you will be drilling, and a second pair of hands for anything heavy.

On the day: make it dead, and keep it dead

  1. Check that your tester works, on a known live source or with its own self-test.
  2. Isolate at the consumer unit; the wall switch alone is not enough. Electrical Safety First's advice for any DIY near wiring is to switch off the power at the fuseboard. Turn off the breaker for the lighting circuit, or take out its fuse; if the labels are missing or you're unsure, use the main switch.
  3. Stop anyone switching it back on. Lock the breaker off if your consumer unit allows it, or tape over it with a note.
  4. Prove it is dead at the light, testing every conductor, including the earth. Never assume a circuit is dead because a breaker is off.
  5. Check the tester again, to be sure it didn't fail in between.

If the light is controlled by an app or a remote, switching it off there does not isolate it either.

Open the rose: read it before you undo anything

Take the cover off the old ceiling rose and photograph the wiring from two or three angles before you loosen a single screw. Then compare what you see with this table.

What you find What it usually means What to do
A single cable coming through the ceiling A simple connection A straightforward swap: follow your light's instructions
Two, three or more cables A "loop-in" rose, which also carries the circuit on to other lights and to the switch Keep your photos and label each wire; if you are unsure which does what, ask an electrician
No earth wire (green-and-yellow, plain green or bare copper) Possible in homes wired before 1966, when the rules did not require one at every light Don't fit a light that has an earth terminal; ask an electrician
Red and black wires Wiring from before the 2004 to 2006 change of colours Not a problem in itself if the cables are sound
Black rubber, fabric or lead-covered cable, or insulation that crumbles Very old wiring, which can deteriorate further when it is handled Stop, and have the wiring inspected
Burn marks, or a light or switch that buzzed or crackled Possible arcing Leave the power off and call a registered electrician

A word on colours. Wiring done from 2004 to 2006 onwards uses brown for live and blue for neutral, where older wiring used red and black. Finding both in one house is normal after a partial rewire, and the official guidance on Part P says that adequate existing cables don't need replacing just because they use the old colours. Still, colours are a guide and never proof, which is why you test.

If there is no earth, our guide to light fittings with no earth wire explains why it matters and what the safe options are.

When to stop and call someone

The loop-in, earth, old-cable and burn-mark rows in that table are all good reasons to stop, and so is doubt. If you don't own a two-pole tester, or you aren't sure how to use one, that is a perfectly good moment to hand over. Swapping a light like-for-like is not notifiable work in England or Wales, as our article on Part P and when you need an electrician explains, so there is nothing to notify either way. If an electrician does the job, ask for a Minor Works Certificate, the record that the finished work was tested.

Once the light is up

Restore the power, switch on, and check that the light works from its switch. If anything flickers or buzzes, switch off at the consumer unit again and ask for help. Choosing your next one? Browse our pendant lights and read the fitting section of each page for the drop and weight. Every order comes with free tracked UK delivery, 30-day returns and a 2-year Lumbury guarantee.

Read more

An oxblood limewashed landing with two travertine half-moon wall lights lit above an upholstered bench, staircase at the side, sunlight on the wall
Fitting & Safety

No Earth Wire? Light Fittings in Older Homes

British homes wired before 1966 may have no earth at the light points. How to tell, why it matters for metal and Class I lights, what the double-square symbol means, and the safe ways forward, best...

Lire la suite
A sage-green Georgian landing with white cornicing, a travertine flush ceiling light lit on the ceiling, a white banister and a sash window in daylight
Fitting & Safety

Do You Need an Electrician to Change a Light Fitting? Part P Explained

In England, replacing a light fitting is not notifiable under Part P, and the law does not say who must do it. What is notifiable, how Wales, Scotland and Northern Ireland differ, and when an elect...

Lire la suite