Article : Lighting Mistakes to Avoid (and the Easy Fixes)

Lighting Mistakes to Avoid (and the Easy Fixes)
The lighting mistakes to avoid at home are few, and nearly all of them come down to a number or a habit: relying on one central light, choosing a fitting the wrong size, hanging it at the wrong height, mixing warm and cool whites, leaving bulbs bare, running everything from one switch, forgetting headroom and pairing LEDs with the wrong dimmer. Each has a simple fix. Here they are in one place, with links to the full guides.
The eight mistakes at a glance
| Mistake | The fix in one line | Read more |
|---|---|---|
| One light in the middle of the ceiling | Add wall lights and lamps: ambient, task and accent | Layered lighting |
| A ceiling light the wrong size | Length + width in feet = diameter in inches | Ceiling light size |
| A pendant too high over the table | 60 to 90 cm from table top to the light's lowest point | Pendant height |
| Warm and cool whites in one room | One colour temperature per room, around 2,700 K in living spaces | 2700K vs 3000K |
| Bare bulbs in your line of sight | Shade them, or choose opal or frosted glass | Opal glass |
| One switch for everything | Separate switches or dimmers for each layer | Stairs and landings |
| No headroom under a pendant | At least 2.1 m clear where people walk | Low ceilings |
| LEDs on the wrong dimmer | Dimmable bulb, LED dimmer, load within its limit | Dimming LEDs |
Mistake 1: one light in the middle of the ceiling, and nothing else
Many British rooms have a single ceiling point, so it is the light everyone uses. On its own it gives flat, uneven light: bright under the fitting, dull in the corners, and nothing where you actually sit and read.
The fix: keep the ceiling light for general light and add two more layers. Wall lights and lamps give the room its evening light; a reading lamp or a picture light gives focus. Even two table lamps in the right corners change a room. The layered lighting guide in the table above explains the three layers and how to plan them.
Mistake 2: a ceiling light that's too small, or too big
A small fitting in a large room looks lost and lights poorly. An oversized one crowds a low room. There's a quick rule of thumb: add up length and width in feet, and that total, read in inches, is the diameter to aim for. Working in metres, multiply that sum by 8.3 for an answer in centimetres. So a 4 by 3.6 m sitting room (roughly 13 by 12 ft) points to a fitting of about 63 cm, or 25 in, across.
The fix: treat the result as a starting point, not a rule, with roughly 10% of leeway in either direction for taste. Cut a circle of card to that size and hold it up before you order; living with it for an evening beats any photograph.
Mistake 3: hanging the pendant at the wrong height over the table
Too high, and the light floods the room instead of the table and you see the bulb from across the room. Too low, and you talk to each other round it. Over a dining table, the number that matters is the gap above the table top, not the drop from the ceiling.
The fix: leave 60 to 90 cm (24 to 35 in) between the table top and the lowest part of the light, and most guides settle on 75 to 90 cm. For the width, a light half the table's width is the minimum and two-thirds the maximum. Over a kitchen island, allow 70 to 90 cm from the worktop to the bottom of each shade.
Mistake 4: mixing warm and cool whites in one room
A 2,700 K lamp beside a cool-white ceiling light makes both look wrong: one too yellow, the other too blue. It happens easily when bulbs are replaced one at a time from whatever is in the drawer.
The fix: one colour temperature per room. Go for about 2,700 K in the sitting room, bedrooms and dining room, and nearer 3,000 K in a kitchen or study. Read the kelvin figure on the box before you buy, and for lights with a built-in LED, check the colour on the product page.
Mistake 5: seeing the bulb
A bare bulb at eye level, or a clear-glass pendant you look straight up into, means glare. Your eyes go to the brightest point and the rest of the room looks darker than it is.
The fix: shade it, move it, or choose glass that hides it. Opal glass spreads the light over the entire shade. Eton, for instance, is a pendant in milk-white opal glass that lights evenly and never dazzles. Wall lights belong at roughly eye level, 1.5 to 1.8 m up, where they limit glare from the sofa.
Mistake 6: one switch for the whole room
If the ceiling light, wall lights and lamps all come on together, you lose the reason for having several lights. The room is either fully on or off.
The fix: give each layer its own switch, ideally a dimmer, so one room can be bright for cleaning on a Saturday morning and low and soft by Sunday evening. On stairs, two-way switching puts a switch at each end, so nobody climbs or goes down in the dark. New switches mean electrical work: an electrician can do this for you if you prefer.
Mistake 7: forgetting headroom
A pendant that looks right in a photo can be a forehead-height hazard in a cottage hall. Where people walk, the floor-to-fitting clearance under anything that hangs should be 2.1 m or more (that's about 6 ft 11 in). Over a stairwell, measure up from the stair underneath it, not from the hall floor.
The fix: under low ceilings and beams, choose flush or semi-flush fittings and let wall lights and lamps do the rest. Tetbury, a disc of travertine that sits directly against the ceiling with no wires showing, is one answer. You'll find more in our ceiling lights.
Mistake 8: LEDs on the wrong dimmer
Flicker at low settings, a faint hum, or a light that won't dim smoothly usually mean the bulb and the dimmer don't suit each other. Older dimmers were made for filament bulbs, and an LED load can fall below their minimum.
The fix: run three checks. Is the bulb marked dimmable on its packaging? Is the dimmer an LED model, normally trailing-edge? And does the combined wattage of every bulb on that dimmer sit inside its LED rating? With a built-in LED, look on the product page to see if it dims, and how. Hexham is a good example of why that matters: its remote-control version sets the brightness, but neither version works with a wall dimmer. Swapping a dimmer means working on mains wiring: switch off at the consumer unit and prove the power is off first, as our fitting guide shows, or ask an electrician.
Two more worth knowing
- Buying by watts. Watts measure power, lumens measure light. An old 40 W bulb is about 470 lm, 60 W about 806 lm, 75 W about 1,055 lm and 100 W about 1,521 lm. See how many lumens you need.
- Guessing in the bathroom. Check the zone first, then the IP rating: IPX4 at least in zones 1 and 2, which reach 2.25 m high. Our guide to bathroom lighting zones sets it out.
A ten-minute check of your own room
- Wait for dusk and switch on every light in the room. Stand in the doorway, then sit where you usually sit.
- Can you see a bare bulb from your chair? Note it.
- Do any two lights look a different white? Compare their kelvin numbers, printed on bulb packaging and on our product pages.
- Are there dark corners, or a dark wall opposite the window? That's where a lamp or a wall light goes.
- Measure the drop over the table and the clearance under any pendant where people walk.
- Turn the dimmer right down. Any flicker or hum? Check the three dimming points above.
Each answer points to one of the fixes above. For every number on a single page, from table heights to lumens, see our free Room-by-Room Lighting Guide.

















