
How to Choose a Wall Light: Eight Questions to Ask
Good wall lights for a living room come from eight plain questions rather than a mood board: how the light is powered, which way it shines, how big it is against your wall, bulb or built-in LED, whether it dims, how the finish sits with your switches, one or a pair, and what it is made of. Answer them in that order and most living room ideas narrow themselves down to two or three lights. One figure sits above all of them: in most rooms, wall lights go between 1.5 and 1.8 m up from the floor.
1. Wired, or no wiring at all?
A wired wall light needs a wall light point, which simply means a cable already brought out through the wall at the spot where the light will hang. If you already have points, perhaps from an older pair of lights, a like-for-like swap is the simplest route. If you don't, you need new ones.
In England, a light added to a circuit you already have only becomes notifiable inside the zone around a bath or shower, though a brand-new circuit always is. Welsh rules go further and cover any new light point in a kitchen, in a room with a bath or shower, or outdoors. Scotland and Northern Ireland each run their own system. An electrician can do this for you if you prefer; what to check before anyone drills is in our fitting guide.
If wiring isn't possible, or you rent, a battery light is the other route. Moreton, for instance, is a rechargeable bar for above a painting or a mirror. We compare the options in wall lights without wiring.
2. Which way should the light go?
This decides the mood more than anything else. There are four main patterns.
- Up and down. Two beams on the wall, one rising, one falling. It lights the wall rather than the room, which can make a sitting room feel calm. Sedbergh is a slim upright light whose light comes out at both ends; Kirkby is a small fluted resin light where a single G9 bulb feeds both beams.
- Diffused all round. A globe or shade in opal or frosted glass spreads soft light into the room and hides the bulb. This is the most useful pattern if the wall lights are your main evening light.
- Soft up and down through glass. Kersey sits between the two: an opal globe in a metal frame that lights the wall gently both upwards and downwards, while the milky glass hides the bulb.
- Downwards only. A cone or hood that lays a pool of light on a console, a chair or the floor below. Useful beside a reading chair, less so as general light.
Up-and-down lights are mainly accent light. Sedbergh's own page describes it that way. If they are the only lights in the room, add lamps or a diffused light as well.
3. How big should it be against the wall?
Measure the wall, not the room. Three numbers matter: the width of free wall between doors, windows and furniture; the height between the light and the ceiling or picture rail; and how far the light stands out from the wall where people walk past.
Sedbergh shows how this works. Its four heights run from 40 to 80 cm, and none of them stands out from the wall by more than 10 cm. Its page puts the two shorter ones on low walls, between two doors or next to a window, and keeps the 60 and 80 cm for walls with more room under the ceiling. Bath is only 22 cm wide, so it fits a narrow gap: beside a staircase, say, or between two doorways.
If you can't picture it, cut a piece of card to the size of the light and tape it to the wall at the height you plan. Live with it for an evening. For the heights themselves, room by room, see how high wall lights should be.
4. A bulb, or a built-in LED?
A light that takes a bulb lets you choose the brightness and colour, and change them later. Kirkby takes a G9 bulb, included; Kersey takes a G9 of up to 7 W, also supplied. Read the cap and the maximum wattage on the product page before you buy replacements.
A built-in LED can make for a slimmer light, with no bulb to buy. Sedbergh and Bath both have one. Look on the product page for the colour of light and for dimming, and ask us if it says nothing: with a built-in LED, what you buy is what you get.
5. Will you want to dim it?
In a living room, almost certainly. Three conditions have to line up: the light or its bulb must be dimmable, the dimmer must be an LED type (trailing-edge, as a rule), and the total load must stay inside the LED range printed on the dimmer. Miss any of them and the usual signs are flicker or a faint hum.
Check each light. Rosedale, a travertine body with one to three opal globes, works with a compatible dimmer switch, which you buy separately. Sedbergh, on the other hand, is not dimmable. If a page says nothing either way, ask before you buy. How to dim LED lights without flicker goes through it step by step.
6. Does the finish go with your switches and other metals?
Look round the room before you choose a finish. Light switches, sockets, door handles, a curtain pole, picture frames and the fender all bring metal into the room, and wall lights sit right among them. Kersey's page puts it well: gold picks up a brass frame or brass handles already in the room, and matt black goes with black switches or other black light fittings.
A simple rule: keep to one or two metal finishes per room, and match the wall lights to the metal nearest them. Sedbergh comes in gold or black plating on a solid copper stem; Bath has a matt gold ring.
7. One light or a pair?
Pairs bring order. Either side of a chimney breast, a mirror, a sofa or a bed, two matching lights make the room feel balanced. A single light suits an alcove, a reading chair or a stretch of wall that needs its own glow. If you're planning a pair, spacing wall lights around a fireplace, mirror or bed has the measurements.
Remember that each light in a pair needs its own wall light point if they are wired.
8. What should it be made of?
The material sets how the light looks when it is on. Opal glass spreads its glow evenly over the whole shade. Stone works differently: on Bath, a hidden LED lights the marble disc from the back; on Sedbergh, the light leaves both ends of a small marble cylinder. Kirkby shows what resin can do: it is sculpted with vertical flutes and comes in four colours, from a white that melts into a pale wall to terracotta, grey or green. Natural stone varies: every marble and travertine piece has its own markings, so yours won't match the photo exactly. Browse our wall lights to see the range of materials side by side.
Putting it together: a 1930s semi sitting room
A typical front room: a chimney breast with alcoves either side, a bay window, one ceiling point. Here is how the eight questions play out.
| Question | Answer in this room |
|---|---|
| Wiring | No wall points yet: two can be added to the existing lighting circuit, by an electrician if you prefer |
| Direction | Light thrown up and down the alcove walls, over the books |
| Size | Alcove walls are narrow, so a slim light, measured against the shelves |
| Bulb or LED | Either, as long as the colour is warm, around 2,700 K, to match the lamps |
| Dimming | Yes, so choose lights whose page says they dim, and fit an LED dimmer |
| Finish | Brass door furniture in the room, so gold |
| Pair | A pair, one in each alcove |
| Height | 1.5 to 1.8 m from the floor |
With the walls lit, the ceiling light becomes optional on most evenings. For the rest of the room, from lamps to colour temperature, The Room-by-Room Lighting Guide has every number on one page.


















