Skip to content

We'll ring you back

Leave your number and a time that suits you: we'll call to talk through your project or a light.

We only use your number to call you back. See our privacy policy.

Basket

Your basket is empty

Article: Dimming LED Lights Without the Flicker

A reading corner in a claret Georgian sitting room with white panelling, a bottle-green velvet wing chair under a lit blue-and-white ceramic wall light, sash window at blue hour

Dimming LED Lights Without the Flicker

LED flickering on a dimmer nearly always comes down to one of three things: a bulb that is not made for dimming, a dimmer designed for old filament bulbs, or too little load on the dimmer for it to work smoothly. Check them in that order. The first two cost nothing to find out, and the third is simple arithmetic.

Before you start, one quick test. Turn the dimmer right up to full. If the flicker stops, the dimmer and the bulbs simply don't suit each other.

What the flicker is telling you

What you see or hear Likely cause What to try
Flicker or pulsing at low settings, steady at full The dimmer is under-loaded, or is the wrong type for LEDs Check the total wattage against the dimmer's LED range; consider an LED dimmer
Flicker at every setting The bulb is not dimmable, or the light is not made for a dimmer Read the bulb box and the product page
A faint hum The dimmer and the bulbs are not well matched An LED dimmer, usually a trailing-edge type
A faint glow when switched off Some LED bulbs glow on the tiny standby current that touch and remote dimmers draw Ask an electrician about a dimmer suited to small LED loads
A loud buzz, crackling, heat or a burning smell Possibly a fault Switch off at the consumer unit, stop using the light and call an electrician

Check 1: is the bulb, or the light, made for dimming?

A bulb has to say "dimmable" on the box. If it doesn't, assume it isn't. Look for the opposite too: a bulb that cannot be dimmed is meant to say "not suitable for dimming" on the bulb or its box. The small G9 and GU10 bulbs in many wall lights follow the same rule (our guide to the smaller bulbs).

Lights with a built-in LED have no bulb to check, so the answer is on the product page. Here is what some of ours say, and several of them cannot be dimmed at all:

  • Southwold, the slim paper disc pendant, has LEDs inside the disc, and its page says the brightness cannot be dimmed.
  • Buxton, the alabaster wall light with warm white LEDs behind the stone, is not dimmable.
  • Hadleigh, the rippled glass ceiling light, does not work with a dimmer. One version offers three light modes, which you step through with the wall switch.
  • Ludlow, the travertine pendant, can be dimmed with a compatible dimmer, which is not supplied.
  • Skipton, the slim LED wall bar, comes in warm, neutral or cool white, or in a dimmable version. Grasmere and Thirsk, two of our flat ceiling lights, also offer a dimmable version.

Two more dim another way. Castleton, the alabaster disc chandelier, can be dimmed only in its remote-control version, and Hexham, the travertine bowl, sets its brightness from a remote; neither of Hexham's versions works with a wall dimmer. If you want a light you can turn down, choose the right version when you order: with a built-in LED, the version you order is the version you live with. Our guide to integrated LEDs and replaceable bulbs goes into that trade-off.

Check 2: leading edge or trailing edge?

Older dimmers were made for filament and halogen bulbs. One British dimmer maker, for example, still sells a leading-edge range for that kind of lighting and says plainly that it is not suitable for LED bulbs. Dimmers made for LEDs are usually trailing-edge: the same maker's programmable LED dimmers start in trailing-edge mode, which it calls the best for most LEDs.

It is not an absolute rule. Some LED bulbs and drivers are designed for leading-edge control, so if a bulb's box or data sheet names a dimmer type, follow it. If your dimmer is more than a few years old and nobody remembers buying it for LEDs, it is a likely suspect.

Check 3: enough load, but not too much

Every dimmer has a range: a maximum and, often, a minimum. Below the minimum, LEDs may flicker, and because LED bulbs use so little power, a single one can fall short. One maker's LED range, for instance, starts at 15, 20 or 40 W depending on the model, and only its smallest model has no minimum at all.

Add up the wattage of every bulb the dimmer controls: the number of bulbs times the watts printed on each. Take a sitting room with a pendant and a pair of wall lights, each with a 5 W dimmable LED bulb. That is 15 W in total, so you need a dimmer whose LED range starts at 15 W or below. Going over the maximum is the opposite mistake, so check both ends of the range.

Why does my dimmer buzz?

A very faint buzz from a dimmer is normal, and some combinations of dimmer and bulb are more prone to it than others. For a buzz you can hear across the room, the usual advice is a trailing-edge dimmer. Sometimes the hum comes from a part vibrating inside the bulb itself; then a different dimmer setting, or a different bulb, is worth trying.

A loud buzz, crackling, heat at the switch or a burning smell is different. Switch off at the consumer unit, stop using the light, and have it looked at by an electrician.

Smart bulbs or a wall dimmer?

A smart bulb does its own dimming, from an app, a remote or a voice assistant. That makes it a good answer in a room where you would rather not change the wall switch. Read its instructions before putting it on a circuit that already has a dimmer, though: two dimmers working against each other is not a combination to guess at.

A wall dimmer suits a light you use every evening and want to control by hand. It also works for every dimmable bulb on that switch at once, which a single smart bulb does not.

Changing the dimmer itself

Swapping a dimmer is mains wiring. In England and Wales, replacing a switch like this is not notifiable work (our article on Part P and electricians explains the rules), but it still has to be done safely. Switch off at the consumer unit, prove the circuit is dead with a two-pole tester, and photograph the wiring before you undo anything. Our fitting guide sets out those safety steps. An electrician can do it for you if you prefer, and can check the load at the same time.

A dimmer is most useful where the evening light matters: the sitting room, the dining table, the bedroom. Browse our lights for the sitting room and read the dimming line on each page before you choose. And if you are working out how many lights to put on each switch, the free Room-by-Room Lighting Guide sets out the three layers of light, with the dimming checks on its bulb page.

Read more

A close view of a lit travertine bar wall light on an oxblood plastered wall above a mahogany console with a soft cloth and brush, sash window at blue hour
Bulbs & Dimming

Integrated LED or a Bulb You Can Replace?

A built-in LED means no bulb to choose and slimmer designs, but colour and dimming are fixed when you order. The honest pros and cons, and the lines to read on a product page first.

Read more
A bottle-green Georgian study lined with books, a ceramic pendant lit over a mahogany writing table, sash window at blue hour
Bulbs & Dimming

How Many Lumens Do You Need? A Room-by-Room Guide

A simple method for working out the lumens each room needs, with suggested lux levels from a recognised UK guide, the official lumens-to-watts table and a worked sitting-room example.

Read more