Skip to content

We'll ring you back

Leave your number and a time that suits you: we'll call to talk through your project or a light.

We only use your number to call you back. See our privacy policy.

Basket

Your basket is empty

Article: Do You Need an Electrician to Change a Light Fitting? Part P Explained

A sage-green Georgian landing with white cornicing, a travertine flush ceiling light lit on the ceiling, a white banister and a sash window in daylight

Do You Need an Electrician to Change a Light Fitting? Part P Explained

Do you need an electrician to change a light fitting in the UK? Not for a straight swap. In England, replacing a light fitting is not notifiable work under Part P of the Building Regulations, and the regulations do not restrict who may carry out electrical work, so you can change one yourself. The job must still be done safely and to the British wiring standard, BS 7671, and an electrician can do this for you if you prefer.

What changes the answer is not the light but the work around it: a new circuit, a new consumer unit, or anything that alters the wiring close to a bath or shower. Here is where the line falls, nation by nation.

What Part P covers

Part P is the part of the Building Regulations that deals with electrical safety in homes. In England the official guidance is Approved Document P (2013 edition). Part P applies to all electrical work in a home, whether a professional or a DIYer does it.

Two points are often missed. First, every job, notifiable or not, should be designed, installed, inspected and tested to BS 7671. Second, if a local authority finds that non-notifiable work is unsafe and does not comply, it can take enforcement action. "Not notifiable" means nobody has to be told before or after. It does not mean anything goes.

Notifiable or not? Common lighting jobs in England

The job Notifiable in England?
Replacing a ceiling light, pendant or wall light, in any room No
Replacing a light fitting in a bathroom No, though Electrical Safety First recommends a registered electrician for bathroom work
A new light on an existing circuit, outside the bath or shower space No
Adding a light, or altering a circuit, in the space around a bath or shower Yes
Running a new circuit from the consumer unit, indoors or out to the garden Yes
Replacing the consumer unit Yes

The "space around a bath or shower" has a precise meaning. It runs from the floor up to 2.25 m (or higher, if the shower head is fixed above that), and out 0.6 m from the edge of the bath or shower tray. Where there is no tray, it reaches 1.2 m from the centre of the shower head. A room with a swimming pool or a sauna heater also counts. Our guide to bathroom lighting zones explains the IP ratings that apply there.

If the work is notifiable: three routes

Notifiable work in England has to be certified in one of three ways:

  1. A registered electrician (a "competent person") does the work and self-certifies it. This is the simplest route.
  2. A registered third-party certifier, appointed before the work begins, inspects and tests work done by someone who is not registered.
  3. Building control is told before the work begins, and decides what inspection and testing it needs.

With the first route, the electrician gives you a BS 7671 electrical installation certificate, and within 30 days of the work being finished you receive a Building Regulations compliance certificate. Keep both somewhere safe. If you go through building control, it issues a completion certificate instead (a final certificate, if a private building control body handled the job).

What a registered electrician gives you on smaller jobs

For work that is not notifiable, such as swapping a pendant, the Planning Portal's advice is that a qualified electrician should give you a Minor Works Certificate. It records what was done and that it was tested. In England and Wales, you can find a registered electrician by postcode on the Registered Competent Person Electrical register, which lists those registered with the government-approved schemes.

The rules in Wales, Scotland and Northern Ireland

Wales

Welsh building regulations have diverged from England's since 2014, and the Welsh list is a little different. According to the Welsh Government's guidance, repairs, replacements and maintenance do not need to be notified, so replacing a light fitting needs no notice. Adding an extra light point does not need notifying either, except in a kitchen, a bathroom or outdoors. Notifiable work goes through a registered electrician or building control, and the same guidance says plainly that the Building Regulations do not restrict who may carry out electrical installation work.

Scotland

Scotland has its own building standards system, and Part P self-certification does not apply there. Replacing a light fitting with one of the same general type does not need a building warrant. The work must still comply with the regulations, and Scotland's standards refer to BS 7671 for electrical safety.

Northern Ireland

Northern Ireland has its own building regulations. According to Electrical Safety First, there is currently no statutory requirement there equivalent to Part P for electrical work in homes, and the charity strongly recommends a competent, registered electrician. For anything beyond a simple swap, your council's building control can tell you what applies.

So when is an electrician the better choice?

Using an electrician is not a legal requirement for a like-for-like swap. But in these situations we would always suggest one:

  • there is no earth wire at the ceiling and your new light has an earth terminal (see what to do when there is no earth wire);
  • the wiring looks old: black rubber, fabric or lead covering, or brittle insulation;
  • you open the ceiling rose and find several cables, and you are not sure which does what;
  • the light is going in a bathroom or outdoors and it is more than a like-for-like swap;
  • you want a light where there isn't one now;
  • the light is heavy and you cannot find a joist to fix it to;
  • you do not have a two-pole voltage tester, or something simply doesn't feel right.

Weight deserves a word. As a guide drawn from the wiring regulations, the fixing for a ceiling light should carry at least 5 kg, and anything heavier needs a joist or a timber batten that can bear its whole weight. Hexham, our travertine bowl that fixes against the ceiling, shows why it matters: the widest, 55 cm across, weighs about 7.7 kg, against roughly 2.8 and 4.8 kg for the two smaller sizes, so that one is a job for a solid fixing.

If you do it yourself

A like-for-like swap looks like this: Harrow, our solid wood dome pendant, connects to your existing ceiling light point, and an electrician can do this for you if you prefer. Whoever does it, three habits matter most. Switch off at the consumer unit, not just the wall switch. Use a two-pole voltage tester to prove nothing is still live. Photograph the wiring before you undo a single screw.

Our fitting guide sets out each step in order, and our checklist for changing a ceiling light covers what to look at before you start. If you are still choosing, browse our ceiling lights, and keep The Room-by-Room Lighting Guide to hand for the heights, sizes and bulbs.

Read more

An oxblood limewashed landing seen from below with a small tinted glass flush ceiling light lit on the ceiling, daytime
Fitting & Safety

Changing a Ceiling Light: What to Check Before You Start

A checklist for changing a ceiling light in a British home: what to measure and look up before the day, how to make the circuit safe, what the old ceiling rose tells you, and when to stop and call ...

Read more
A close view of a lit travertine bar wall light on an oxblood plastered wall above a mahogany console with a soft cloth and brush, sash window at blue hour
Bulbs & Dimming

Integrated LED or a Bulb You Can Replace?

A built-in LED means no bulb to choose and slimmer designs, but colour and dimming are fixed when you order. The honest pros and cons, and the lines to read on a product page first.

Read more