
E14, G9 and GU10: A Guide to the Smaller Bulbs
A G9 bulb is a small capsule with two looped pins 9 mm apart, which push straight into the holder with no twist. It runs on mains voltage and is the bulb inside many small glass globes and wall lights, several of ours among them, where LED versions now take the place of the old halogen capsules. Its two neighbours are different again: E14 is a small screw, and GU10 is a spotlight bulb that pushes in and twists to lock.
None of the three swaps for another, or for the larger B22 and E27 bulbs. The good news is that each is easy to recognise once you know what to look for.
The small caps at a glance
| Cap | What it looks like | How it goes in | Lumbury lights whose page names it |
|---|---|---|---|
| E14 (small Edison screw, or SES) | A screw thread 14 mm wide | Screws in | Broadway, Bibury, Orford, Bourton |
| G9 | A small capsule with two looped pins 9 mm apart | Pushes straight in | Painswick, Rosedale, Ripon, Kersey, Kirkby, Eyam, Clare |
| GU10 | A short, wide bulb with two stubby pins 10 mm apart | Pushes in, then twists to lock | Henley, Winchcombe, Amberley |
| G4 | A tiny capsule with two thin pins 4 mm apart | Pushes straight in | Wells, Haworth |
As with the larger bulbs, the letters and numbers tell the story. E is for Edison, the screw family, and the figure is the diameter in millimetres. G is for a pin base, and the figure is the distance between the pins. If you are not sure which large cap you have, our guide to B22 and E27 covers those.
G9: the capsule inside the globe
You will meet the G9 most often in wall lights, where a small glass globe or shade surrounds it. On Painswick, a ring of natural stone around a frosted glass globe, the bulb is a G9 and an LED one is included; the frosted globe keeps the bare bulb out of sight. Rosedale sets one to three opal globes on a travertine body, and each globe takes a G9 bulb of up to 7 W, with the bulbs in the box.
Because a G9 pushes in rather than twisting, removing one is a straight, gentle pull. Hold the bulb itself, not the glass around it.
GU10: the spotlight bulb
The GU10 is the short, wide bulb you find in spotlights and reading lights. Its job is to throw light in one direction, which is why it suits a lamp you aim. Henley is a ceiling light with three fluted wood spots that tilt one by one. Every head holds a GU10 of no more than 10 W, and the box contains all three bulbs. Winchcombe, a swing-arm reading light, ships with its GU10 LED bulb, warm white or cool white according to the version you order.
Do not mix up GU10 with GU5.3, the base often used on the bulbs called MR16. They look alike, but a GU5.3 has thin pins about 5.3 mm apart, and it will not fit a GU10 holder.
E14: the small screw
E14, also called SES, is the little brother of the E27. It is common on chandeliers, small table lamps and some pendants. In our range it lights the sculpted glass of Broadway, an Art Deco wall light that comes with its E14 bulb (40 W at most), as well as the fluted glass globe of Bibury and the smooth glass globe of Orford, which both arrive with an E14 LED bulb.
LED versions: what to look for
All three caps come in LED versions, and every Lumbury light that names one of these caps comes with its bulb. When the day comes to replace it, choose by three things.
- Brightness in lumens, not watts. About 470 lm matches an old 40 W bulb, so compare that figure rather than the watts.
- The colour of the light. Match the warm or cool white of the bulb you are replacing, so the light does not change from one evening to the next. Winchcombe, for example, comes in a warm white version and a cool white one.
- The size. Measure the old bulb, or the space inside the globe or shade, before you buy, so the new one fits without touching the glass.
Will a G9 LED bulb dim?
Only if two things are true. The bulb must say "dimmable" on its box (a bulb that will not dim should carry a "not suitable for dimming" mark), and the light itself must allow it. The product page tells you which.
- Rosedale can run from a dimmer switch as long as the dimmer is compatible. The dimmer itself is not supplied.
- Henley needs dimmable GU10 bulbs and a dimmer switch.
- Broadway can be turned down once it has a dimmable bulb and a suitable dimmer on the wall.
- Eyam and Clare, two of our G9 wall lights, are not made for a dimmer, and neither are Bibury, Orford or Winchcombe.
If you do dim, the dimmer matters as much as the bulb. Our article on dimming LEDs without the flicker explains what to check.
Heat and the maximum wattage
Every lampholder has a maximum wattage, printed on the holder or the product page, and Electrical Safety First's advice is never to go above it. With small bulbs the limits are low: up to 7 W for the G9 bulbs of Rosedale and Kersey, up to 10 W for each GU10 on Henley, 40 W at most for the E14 on Broadway, and 5 W for the G4 on Haworth. When you buy a replacement, check its watts against that limit as well as its cap: two G9 bulbs can look identical and draw different power.
How to change a small bulb safely
- Switch off. For a light wired into the wall or ceiling, Electrical Safety First recommends switching off the circuit before removing or replacing an LED bulb. For a lamp, unplug it.
- Let it cool. Give the old bulb a few minutes before you touch it.
- Read the old bulb. Note the cap, the wattage and the colour of the light before it goes in the bin.
- Remove it the right way. Pull a G9 or G4 straight out, twist a GU10 back and then pull, unscrew an E14.
- Fit the new one and check it sits fully home before you close the globe or shade.
- Buy from a brand you know. Electrical Safety First has found LED bulbs on the market with live parts that could be touched. A well-made bulb is marked with its maker or brand, its voltage and its wattage.
Quick questions
GU10 or G9: which is better?
They are not alternatives: the light decides. A GU10 throws a beam, which suits a reading light or a spotlight. A G9 usually sits inside a globe or shade that softens its light, as on Painswick, whose frosted globe hides the bulb, or Kersey, whose opal glass diffuses the glow.
Can I put a G9 bulb in a G4 holder?
No. The pins are a different distance apart, so the bulb will not seat properly. Buy the cap the product page names.
Most of our lights with small caps are wall lights: 14 of the 16. Browse our wall lights to see them together, and if you are planning a bedside light, our guide to bedside wall lights covers height and reach. For every cap on one page, along with lumens and kelvins, keep a copy of our free Room-by-Room Lighting Guide to hand.


















