Passer au contenu

On vous rappelle

Laissez votre numéro et le moment qui vous arrange : nous vous appelons pour parler de votre projet ou d'un luminaire.

Votre numéro sert uniquement à vous rappeler. Voir notre politique de confidentialité.

Panier

Votre panier est vide

Article : Integrated LED or a Bulb You Can Replace?

A close view of a lit travertine bar wall light on an oxblood plastered wall above a mahogany console with a soft cloth and brush, sash window at blue hour

Integrated LED or a Bulb You Can Replace?

An integrated LED light fitting has its light source built in: you never buy, fit or replace a bulb. Several of ours state a life of around 50,000 hours. The trade-off is that a sealed LED module cannot be swapped like a bulb, and the colour of the light and whether it dims are fixed by the version you order.

Neither is better in every room. A built-in LED makes possible shapes that a bulb never could; a bulb lets you change your mind for years. Here is how to weigh the two, and what to look for on a product page before you decide.

Built-in LED or bulb: the short comparison

Built-in (integrated) LED Replaceable bulb
Choosing a bulb Nothing to choose: the LED arrives fitted You choose the brightness and colour, within the cap and maximum wattage the light names
Shape Can be very slim, or lit from behind or below Needs room for a lampholder and a bulb
Colour of the light Chosen when you order; some versions switch between whites Changed whenever you change the bulb
Dimming Fixed by the version: dimmable, remote-controlled or not at all Set by the bulb, the dimmer and the light together
Stated life Around 50,000 hours on several of ours Depends on the bulb you buy
When the light source fails A sealed module cannot be replaced on its own A new bulb

What "integrated" looks like on a product page

The words vary, but the meaning is the same. Look for "integrated", "built-in", "fitted and sealed" or "no bulb on show". Our product pages name the light source in the section headed "The light":

  • Bath, a disc of natural marble with a gold-finish ring, has an integrated LED, included, which lights the disc from behind.
  • Malton, a solid block of travertine, hides its integrated LED under the stone, so no bulb is on show and the light shines down the wall.
  • Ambleside, a hanging metal disc, has a built-in LED behind an acrylic panel: 12 W for the 25 cm disc and 24 W for the 40 cm, in 3000K warm white.

A light that takes a bulb names its cap instead. Take Harrow, the ribbed wooden dome: its page names an E27 cap, the first bulb comes in the box, and any standard E27 can take over when that one fails. If the cap codes are new to you, our guide to B22 and E27 bulb caps explains them.

Where a built-in LED earns its place

Slim shapes. With no lampholder to house, a light can sit very close to the wall or ceiling. Malton is only 5 cm deep, and Ambleside's 25 cm disc is 5.5 cm deep. That matters under a low cottage ceiling or in a narrow hall.

Light that comes from the material. A small LED can sit behind stone or inside a frame where no bulb would fit. Bath's marble is lit from the back; Castleton, a spiral of alabaster discs on a gold frame, is lit by built-in LED strips.

No bulb to choose. There is nothing to get wrong on the day it arrives: no cap to match and no wattage to check.

Where a bulb you can change wins

You can change your mind. If the room feels too cool, too bright or too dim, a different bulb fixes it. With a built-in LED, the white you order is the white you keep, unless that version is one that switches between whites. Southwold, for instance, lets you pick warm, neutral or cool white when you order, and Salcombe's page says its white cannot be changed afterwards.

Dimming stays open. On a light that allows it, a dimmable bulb and the right dimmer give you dimming later. A built-in LED dims only if that version was made to, and some do it by remote rather than from the wall: Castleton, for one, dims only in the version sold with a remote control. Our article on dimming LEDs without the flicker covers both.

The end of the light source is not the end of the light. When a bulb fails, you replace the bulb.

How long is 50,000 hours?

Tetbury, Kendal, Ludlow, Southwold, Bakewell, Burford and Dedham each give a life of around 50,000 hours on their page. Used three hours every evening, that is more than 45 years; used six hours a day, nearly 23. Even a light left on twelve hours a day would pass eleven years.

Treat the figure as the maker's estimate for the LED, not a promise. What Lumbury guarantees is two years against manufacturing defects, on top of your statutory rights. If anything goes wrong within that time, write to us.

Can you replace an integrated LED?

Not on a sealed module, and several of our pages say so outright: Tetbury, Kendal, Ludlow, Burford and Dedham all state that their LED cannot be replaced. Dedham's page puts it plainly: the module cannot be swapped, which is worth knowing before you order. We would rather you knew that now than discovered it in ten years. Where a page doesn't say either way, ask us before you buy.

Six lines to read before you order

  1. The light source. A cap code (E27, E14, G9, GU10) means a bulb; "integrated", "built-in" or "sealed" means an LED you keep.
  2. Whether it can be replaced. Look for "cannot be replaced" or "cannot be swapped".
  3. The colour, in kelvin. 3,000 K is a warm white. Check whether you choose it when ordering, and keep one colour per room (2700K or 3000K?).
  4. The dimming line. "Not dimmable", "with a compatible dimmer" and "remote control" mean three different things.
  5. Power and brightness. Watts and lumens, where the page gives them. Bakewell, for example, gives 18 W (1,800 lumens) to 36 W (3,600 lumens) depending on size. To judge whether that is enough, see how many lumens a room needs.
  6. The stated life. Useful for comparing, as long as you read it as an estimate.

A practical way to decide: put built-in LEDs where shape matters most and you are sure of the colour you want, such as a slim wall light in a hall or a flush light under a low ceiling. Keep bulbs where you expect to fiddle, such as a reading corner or a dining table you may want to dim. Browse our wall lights to see both kinds side by side, and for every bulb and colour figure on one page, take a copy of our free lighting guide.

Read more

A sage-green Georgian landing with white cornicing, a travertine flush ceiling light lit on the ceiling, a white banister and a sash window in daylight
Fitting & Safety

Do You Need an Electrician to Change a Light Fitting? Part P Explained

In England, replacing a light fitting is not notifiable under Part P, and the law does not say who must do it. What is notifiable, how Wales, Scotland and Northern Ireland differ, and when an elect...

Lire la suite
A reading corner in a claret Georgian sitting room with white panelling, a bottle-green velvet wing chair under a lit blue-and-white ceramic wall light, sash window at blue hour
Bulbs & Dimming

Dimming LED Lights Without the Flicker

Flicker, buzz or a faint glow when the light is off usually means the bulb, the dimmer or the load is wrong. Three checks to run in order, and what our built-in LED lights can and cannot do.

Lire la suite